SSD1500-XY
Reinforcement Plate Punching Press
This device is suitable for the production of sheet products and reinforcement plates, particularly those used in flexible printed circuit boards. It is a press machine equipped with a punching function to process strip-shaped reinforcement plates/reinforcement film material products while moving them with an XY two-axis work feeder.
Press Section
An 11kW (15-ton) AC servo motor is installed, enabling the punching of a wider variety of products. The press uses a high-rigidity four-pillar underdrive system, providing a highly stable mechanism. In addition to the basic functions of the press, the following special functions are included:
Waiting Time (Timing Settings)
1.Intermediate Point Waiting: Stops the slide at the intermediate point to prepare the cutting tool.
2.Cutting Bottom Waiting: Stabilizes the shape of the punch and the punched workpiece within the die.
3.Pushback Waiting: Stabilizes the return of the workpiece during punching using the pushback method.
Cutting Operation Selection
1.Low-Speed Cutting: High speed to the bottom dead center → Low speed to the cutting bottom → High speed to the top dead center.
2.Double Cutting: High speed to the bottom dead center → High/Low speed to the cutting bottom → High speed to the bottom dead center → High/Low speed to the cutting bottom → High speed to the top dead center.
Feeder Section
The feeder section consists of a lightweight X/Y-axis transport table driven by a stepping motor and ball screw. This allows efficient processing of products by setting and registering coordinates. The following data is handled:
・Work Origin (HOME): Can be set at any position, making it easy to shift the setup program.
・Position Data: Can be set as absolute or relative (incremental) values based on the work origin (Effective stroke X-axis: 200mm / Y-axis: 300mm).
| Item | Specifications | Remarks |
|---|---|---|
| Basic Specifications | ||
| Machine Dimensions | 1240mm (W) × 1280mm (D) × 1450mm (H) | |
| Machine Weight | 2000㎏ | |
| Control Power Supply | Operating Circuit: D24V, Power Circuit: AC200/220V | |
| Safety Device | Light Beam Safety Device | During press descent: Power OFF brake activation During press stop: Servo OFF brake activation |
| Supply Power | 3φ 200V・50/60Hz・16kVA | Voltage fluctuation within ±10% |
| Supply Air Pressure | 0.5MPa or higher | Dust-proof and moisture-proof |
| Environmental Conditions | Temperature: 0–30°C, Humidity: 70% or less | No freezing or condensation |
| Press Section | ||
| Maximum Punching Capacity | 150kN（150ton） | Maximum load duration: 5 seconds or less |
| Applicable Die Size | 280mm × 300mm (Core Material: 250mm × 300mm) | Effective punching range: 200×240mm |
| Maximum Stroke Length | 90mm (with standard type installed) | 170mm: Between fixtures |
| Drive System | Ball screw drive by AC servo motor | |
| Control System | Semi-closed digital positioning | Control resolution: 0.001mm/pulse |
| Speed | 1–10m/min (constant speed), rated 10m/min | Adjustment High speed: 10–100% override of the rating Low speed: 1–10cm/min |
| Position Setting | 0.01mm / 0.1mm (switchable at any time) Setting Values: Top dead center, intermediate point, bottom dead center, cutting depth | Setting method: By pulse handle Can be set at any position |
| AC Servo Motor | 11kW 2000rpm | |
| Brake | Combination of drive shaft restraint and built-in motor brake | Dynamic brake also used when motor is operating |
| Feeder Section (X-axis/Y-axis) | ||
| Effective Stroke | X-axis: 200mm / Y-axis: 300mm | |
| Drive System | Ball screw drive by stepping motor | |
| Control System | Digital positioning by open-loop | |
| Speed | 18m/min | Adjustment: 10–100% override of the rating |
| Position Setting | Setting Unit: 0.01mm Type: Switchable between absolute and incremental | Setting method: By numeric keypad |
| Maximum Position Setting Count | 60 | |
| Maximum Program Setting Count | 16 |
(You can download it through the database site “EMIDAS”.
Membership registration on EMIDAS is required for download.)
